- Jump starter and Power Bank with lithium battery (technology LiFePO4 = Lithium - Iron - Phosphate).
- Quick start of motorcycles, cars and vans with 12V and 24V battery.
- SMART BOOSTER TECHNOLOGY It protects against reverse polarity and short circuit and it prevents jump start operation if the FAST battery is discharged (voltage below 11V), preserving the device itself.
- Powering smartphones, tablets and other commonly used portable devices.
- High J-BME3s: it is the energy supplied by the jump starter within three seconds of cranking to keep the engine run.
- Reduced weight and size, the lithium battery stores four times the energy of a lead battery with the same weight.
- Quick charge
- High brightness LED lamp, with selectable fixed lighting, flashing alarm and SOS signal.

Technical details:
- Input voltage : 1 Ph - 100/240V 50/60 Hz
- Boosting voltage (Volt) : 12-24V
- Boosting current max (Amp) : 12V 3000A - 24V 2000A
- Boosting current (1V/C) (Amp) : 12V 700A - 24V 500A
- Battery capacity : 35000mAh
- Battery types : Automotive: Pb (WET - AGM - GEL)
- J-BME3s (Joule-Battery Maximum Energy) : 20000J
- For engines up to - Ta=25°C - (Petrol) : 8000cc
- For engines up to - Ta=25°C - (Diesel) : 5000cc
- USB 1 output : 5V - 2,1A
- USB 2 output : 5V - 1,0A
- DC output : 12V - 10A
- Input (Jack) : 15V - 1A
- Charging time : 7h
---------
Made In Italy

- Fully automatic battery chargers built with electronic charge control and charging conservation "Floating".
- Suitable for charging lead batteries: WET serviceable and maintenance free, AGM, AGM Power, GEL, Start & Stop, Ca/Ca.
- Multi step chargingThe batteries are charged by applying sophisticated multi-step programs.
- High efficiency " I-U " Charging characteristic (constant current-constant voltage) minimises battery charging time.
- FloatingCan remain connected to the battery for a long time. Batteries are ready to use at all times.
- Safety guaranteed Designed to protect vehicle electronics. Non-sparking. Reverse polarity protected and short-circuit proof. Charging voltage is free of interference and voltage peaks. Allow battery charging directly on the vehicle electrical system, without disconnecting the battery. (DIN 40839 interference emission level I)
- Battery Test Sulphated battery detection.
- "Sulfated Battery Recovery" Desulphation / Equalization programme. Regenerate batteries that have underdone heavy discharge cycles.
- Battery charger suitable for the workshop.

Technical details:
- Input Voltage (Volt 50-60Hz AC) : 1 Ph - 230V
- Power (W) : 530W
- Voltage limitation (Volt) : 7,4 - 14,8 - 29,6V
- Nominal battery voltage (Volt) : 6 - 12 - 24V
- Average charging current (Amp) : 3,0 - 6,5 - 13A
- Effective charging current (Amp) : 22A
- Battery capacity (Ah min/max) : 15 / 260Ah
- Battery types : Automotive: Pb (WET - AGM - GEL)
- Charging programs : 2
- Charging positions (N°) : 3
---------
Made In Italy

- The welding power sources of the I-ARC 200 line offer a high duty cycle while being compact and easy to handle. They are the ideal choice for maintenance and small workshop jobs. A reliable and durable product, designed and manufactured with care at our San Marino factories.
- The I-ARC 217 GEN delivers 170 Amps in direct current for welding electrodes from 1.6 to 4.0 mm in diameter. Welds with rutile and basic coated electrodes on various metals: steel, stainless steel, cast iron, etc.
- With the special torch it allows you to weld in TIG mode with "scratch" arc ignition.
- The I-ARC 217 GEN is equipped with special input protections that allow for adequate welding performance even in case of non-optimal power supply. This feature is particularly useful for those who often work by connecting to motorcycle generators (see the characteristics table).
- The I-ARC 217 GEN is easy to use thanks to the welding aid systems:
- Hot Start: facilitates arc striking.
- Arc Force:helps prevent electrode sticking to workpiece by temporarily increasing the current when the electric arc becomes too short.
- Anti-sticking: allows you to easily detach the electrode if it remains glued to the piece.

Technical details:
- Welding current range (Amp) : 10 - 170A
- Duty Cycle (Amp) (DECA use at 20°C) : 170A - 60%
- Duty Cycle (Amp) (EN 60974-1 40°C) : 170A - 20%
- 100A - 60%
- Open circuit voltage (Volt) : 88V
- Input voltage (50/60 Hz) : 1 Ph - 230V
- Absorbed power 60% / Max : 2,8 / 4,9 kW
- Fuse (Amp) : 16A
- Generator : +/- 30% (7 Kw)
- Efficiency : >80%
ELETCTRODES:
- Rutile : Ø 1,6 - 4,0 mm
- Basic : Ø 2,0 - 4,0 mm
- TIG : Ø 1,0 - 4,0 mm
- Output connection : DX 25 mm2
- Thermostatic Protection : yes
---------
Made In Italy

- The electromechanical generators for welding of the P-ARC line are the classic offer of robust and durable systems. They are the ideal choice for craftsmen, blacksmiths, maintenance workers and heavy carpentry. They meet -professional and specialist welding needs and are guaranteed by the LAB mark of excellence. Carefully designed and manufactured at our San Marino factories.
- The P-ARC 840 LAB delivers 400 Amps of direct current to weld electrodes from 1.6 to 8.0 mm in diameter. Welds with rutile and basic coated electrodes on various metals: steel, stainless steel, cast iron, etc. The power supply voltage is three-phase at 230/400 Volt.
* The P-ARC 840 LAB is easy to use:
- Continuous regulation of the welding current.
- Forced ventilation.

Technical details:
- Welding current range (Amp) : 70 - 400A
- Duty Cycle (Amp) (EN 60974-1 40°C) : 380A - 35% / 250A - 60%
- Open circuit voltage (Volt) : 70 - 76V
- Input voltage (50/60 Hz) : 3 Ph - 230/400V
- Absorbed power 60% / Max : 9 / 17 kW
- Fuse (Amp) : 63/40A
ELETCTRODES:
- Rutile : Ø 2,0 - 8,0 mm
- Basic : Ø 2,0 - 5,0 mm
- Output connection : DX 70 mm2
- Thermostatic Protection : no
---------
Made In Italy

- The Dent Puller SW 28 LAB welding power source meets professional and specialist welding needs and is guaranteed by the LAB mark of excellence. Designed and manufactured with care at the San Marino factories.
- The SW 28 LAB model is specifically designed for bodywork work, repairing dents and straightening thin steel sheets. It offers different functions for many uses through the various accessories.
- The SW 28 LAB model delivers 4500 Amp. The power supply voltage is single phase at 230 Volt.
The main features are:
> Easy to use: time and power adjustment is indicated in a help table.
> Gun with trigger: the welding spot is controlled through the trigger.
> Tack mass: for an easy and safe connection to the workpiece.
> Single-sided single-point welding.
> Single-sided pulsed spot welding for patches.
> Continuous welding.
> Sheet metal heating function with carbon electrode
> Gun with quick coupling to easily replace tools.

Technical details:
- Welding current range (I2 MAX) : 4500A
- Welding current range (I RMS) : 400 - 2800A
- Open circuit voltage (Volt) : 2,4 - 7,4V in 50 steps
- Input voltage (50/60 Hz) : 1 Ph - 230V
- Max input power (kW) : 50% / Max = 2,7 / 4 kW
- Open circuit voltage : 2,4 - 7,4V in 50 steps
- Input voltage : 1 Ph - 230V 50/60 Hz
- Fuse : 16A
- Weldable metals : Steel, inox, galvanized steel
FEATURES:
- Power setting : yes
- Time setting : yes
- Welding parameters chart : yes
- Single spot welding : yes
- Pulsed spot welding : yes
- Continuous spot welding : yes
- Carbon heating electrode : yes
- Copper Transformer : yes
- Thermostatic Protection : yes
---------
Made In Italy

- "MICROPROCESSOR" optimizes the welding parameters
> a) "SYNERGETIC ADJUSTMENT" Automatically sets the welding parameters according to the selected tool and the workpiece thickness.
> b) Adjustable time and spot welding current.
> c) Two-digit instrument for adjustable welding current setting.
> d) Possibility of using at the same time a spot gun and a studder gun in order to avoid any waste of time in tools fitting up.
- "PULSE" Continuous single spot and pulsed single spot for sheet metals high yield strength and galvanized steel.
- "SURE SPOT" Automatic compensation grants all welding spots evenness.

Technical details:
- Welding current range (I RMS) : 200 - 8000A
- Open circuit voltage (Volt) : 0,8 10,1V in 99 steps
- Welding capacity : 3 + 3 mm
- Spots/Hour (0,8 + 0,8 mm) N° : 600
- Spots/Hour (3 + 3 mm) N° : 75
- Input voltage (50/60 Hz) : 1 Ph - 400V
- Installation power : 11,2 kW - 50% / 47,0 kW - 100%
- Fuse (Amp) : 32A (D)
- Weldable metals : Steel, inox
FEATURES:
- Synergic : yes
- Pulse : yes
- Sure Spot : yes
- Welding parameters chart : yes
- Single spot welding : yes
- Pressure reducer included : yes
- Trolley complete with arm support : yes
- Equipped for torch water cooling system : yes
- Copper Transformer : yes
- Thermostatic Protection : yes
---------
Made In Italy